-
1 laser weld tempering time
Автоматика: длительность отпуска шва при лазерной сваркеУниверсальный англо-русский словарь > laser weld tempering time
-
2 laser weld tempering time
English-Russian dictionary of mechanical engineering and automation > laser weld tempering time
-
3 laser weld tempering time
Англо-русский словарь промышленной и научной лексики > laser weld tempering time
-
4 time
время; период; продолжительность || устанавливать время; распределять время; рассчитывать по времени; согласовывать во времени; синхронизироватьtime in use — время использования; время работы (напр. инструмента)
time on machine — время пребывания ( обрабатываемой детали) на станке
- acceleration timeto cut time — сокращать время (напр. обработки)
- access time
- activation time
- active maintenance time
- active repair time
- activity time
- actual in-cut time
- addition time
- additional time
- adjustable laser ramp-up time
- administrative time
- aggregate travel time
- air-cutting time
- arcing time of pole
- assembly time
- assessed mean time to failure
- ATC time
- attended running time
- attenuation time
- auxiliary time
- available machine time
- available machining time
- available time
- average access time
- average time
- base cycle time
- batch change time
- batch lead time
- batch run time
- block execution time
- block processing time
- bounce time
- braking time to standstill
- braking time
- break time
- breakdown time
- bridging time
- build time
- build-up time
- cam idle time
- cell production time
- changeover cut-to-cut time
- changeover time
- characteristic time
- charge time
- chip-cutting time
- chip-making time
- chip-to-chip toolchange time
- clock cycle time
- closing time
- combined travel/load time
- commissioning time
- component cycle time
- component inspection time
- component time
- computed machine time
- computing time
- control flow time
- control time
- conversion time
- correction time
- corrective maintenance time
- c-percentile storageability time
- c-percentile time to failure
- cumulative cutting time
- cure time
- current fall time
- current rise time
- cut time
- cutting time
- cut-to-cut time
- cycle time
- dead cycle time
- dead time
- debugging time
- delay time
- delivery time
- depalletizing time
- derivative action time
- derricking time
- detection time
- direct manufacture time
- disengaging time
- division time
- door-to-door time
- double-stroke time
- down time
- dry-cycle time
- dwell time
- effective cutting time
- effective dead time
- empty running time
- end-of-job time
- equispaced times
- equivalent running time for wear
- eroding time
- erosion time
- estimation time
- execution time
- exposure time
- fall time
- fast response time
- finishing time
- first-off machining time
- fitting time
- fixture lead time
- floor-to-floor time
- flow time
- forward recovery time
- frame time
- full brazing time
- full operating time
- full soldering time
- gate controlled turn-off delay time
- gate controlled turn-off fall time
- gate controlled turn-off time
- grinding time
- gripper-changing time
- head-changing time
- hobbing time
- holding time
- idle time
- index time
- indexing time
- innovation time
- in-process time
- integral action time
- interarrival time
- interoperation time
- interpolation delay time
- jaw-adjusting time
- job completion time
- job finish time
- laser interaction time
- laser shutter opening time
- laser weld tempering time
- laser-beam dwell time
- laser-beam interaction time
- lead time
- learning time
- loading time
- machine down time
- machine repair time
- machine run time
- machine slack time
- machine wait time
- machine-setting time
- machine-setup time
- machining floor-to-floor time
- machining time
- machining-cycle time
- maintenance down time
- maintenance time
- make time
- manual machining time
- manufacturing cycle time
- manufacturing lead time
- material to end product lead time
- maximum resetting time
- mean time between failures
- mean time to failure
- mean time to repair
- measuring run time
- metal-to-metal time
- minimum accelerating time
- minimum braking time
- move time
- moving time
- multiplication time
- NC machining time
- NC program debug time
- no-failure operating time
- noncut time
- noncutting time
- nonmachining time
- nonproductive machine time
- nonrequired time
- numerical processing time
- observed mean time to failure
- off-machine process time
- off-shift machine down time
- off-shift slack time
- opening time
- operate time
- operating spindle time
- operating time
- operation cycle time
- operation time
- operator's attention time
- operator's reaction time
- operator's time
- optimized contact time
- out-of-cut machine time
- out-of-cut time
- output cycle time
- overall cycle time
- overall lead time
- pallet change time
- pallet processing time
- pallet shuttle time
- parasitic time
- part turnaround time
- partial operating time
- part-waiting time
- payback time
- periodic time
- pickup time
- piece sequence time
- piece time
- planned loading time
- planning lead time
- planning time
- predicted mean time to failure
- preparatory time
- preset operating time before corrective adjustment
- preset operating time
- preset time
- probing time
- process response time
- process time
- processing time
- product development lead time
- product flow time
- product lead time
- production lead time
- production time per piece
- production time per unit
- production time
- productive time
- profiling time
- programming time
- prorated time
- protective power time
- pulse decay time
- pulse response time
- pulse rise time
- pulse time
- queue time
- queueing time
- rapid response time
- reading time
- readout time
- real time
- rechucking time
- recognition time
- recovery time
- release time
- releasing time
- remaining life time
- repair/down cost time
- required time
- reset time
- residence time of materials
- response time
- restoration time
- return time
- reverse recovery current fall time
- reverse recovery current rise time
- reverse recovery time
- rise time
- robot down time
- roughing time
- run time
- running time
- running-in time
- safety lead time
- sampling time
- scan time
- schedule time
- scheduled time
- sensing time
- series machining time
- service time of the tool
- servicing time
- servo update time
- setter time
- setting time
- settling time
- setup time
- ship time
- slack time
- soaking time
- software execution time
- specified no-failure operating time
- specified operating time
- specified time
- spindle cutting time
- spindle run time
- stabilization time
- stand time
- standard handling time
- standard piece time
- starting time
- start-up time
- station time
- station-to-station time
- step response time
- stopping time
- storage cycle time
- storage time
- storageability time
- switching time
- switch-over time
- system time
- table-indexing time
- tape-preparation time
- tape-turnaround time
- target build time
- target time
- teach time
- throughput time
- time of starting
- tool change time
- tool exchange time
- tool index time
- tool life time
- tool-cutting time
- tool-in-cut time
- tooling-response time
- tool-setup time
- tool-to-tool changing time
- total access time
- total changeover time
- total equivalent running time for strength
- total equivalent running time for wear
- total manufacturing cycle time
- total running time
- total sequence time
- to-the-minute time
- transfer time
- transient time
- transit time
- transition time
- traveling time
- turnaround time
- turn-off time
- turn-on time
- undetected failure time
- unit cycle time
- unit production time
- unit time
- up time
- update time
- updating time
- vehicle time per hour
- vehicle-use time
- waiting time
- wakeup time
- warm-up time
- wasted time
- work-change time
- work-cycle time
- work-in-process time
- wrench time
- zero ATC timeEnglish-Russian dictionary of mechanical engineering and automation > time
-
5 длительность отпуска шва при лазерной сварке
Automation: laser weld tempering timeУниверсальный русско-английский словарь > длительность отпуска шва при лазерной сварке
См. также в других словарях:
steel — steellike, adj. /steel/, n. 1. any of various modified forms of iron, artificially produced, having a carbon content less than that of pig iron and more than that of wrought iron, and having qualities of hardness, elasticity, and strength varying … Universalium
Metalworking — Machining a bar of metal on a lathe. Metalworking is the process of working with metals to create individual parts, assemblies, or large scale structures. The term covers a wide range of work from large ships and bridges to precise engine parts… … Wikipedia
Oxy-fuel welding and cutting — Oxyacetylene redirects here. For the song, see Cubanate. Side of metal, cut by oxygen propane cutting torch … Wikipedia
List of nanotechnology applications — Part of a series of articles on Nanotechnology … Wikipedia
